Rental Equipment
-
Preowned Wacker Neuson SW16
Used Wacker Neuson SW16 ~300hrs, hours may go up slowly as it is used around the yard and rented out occasionally.Unit will be equipped with a bucket when sold, not with pallet forks. 56hp Kohler KDI Diesel Engine 6,170lbs Operating Weight Rated Operating Capacity of 1,600lbs 12mpg Max Travel Speed 20gpm Aux Hydraulic Flow 30gal Fuel Capacity 135" Machine Length with Bucket 34.1" Dump Reach 90.6" Dump Height 118" Hinge Pin Height 7.6" Ground Clearance 5,300lbs Bucket Breakout Force Located at Diamond R Equipment in Higginsville, MO
-
IronCraft Post Hole Digger
IronCraft Post Hole Digger All rental equipment is available at our Higginsville location: Address:19677 NW Outer RdHigginsville, MO 64037 Phone:660-584-8757 Contact us for availability, rates, and booking.
-
Preowned SCAG Cheetah 61" 29hp EFI
2014 SCAG Cheetah 61" 29hp Kohler EFI Model Number: SCZ61V-29CV-EFI $150 Daily $575 Weekly 61" 7 Gauge Velocity Deck Hydrogear ZT5400 Transaxles with a High/Low 13gal Fuel Capacity, Dual Tank ~1,360hrs
-
Mustang 250Z Excavator
Mustang 250z Excavator $240.00 Daily $840.00 Weekly 20hp Yanmar Diesel 11gal Fuel Capacity 9.8" Rubber Tracks, 12.6" Ground Clearance, 4.4-4.6psi Ground Pressure 5,919lbs Operating Weight 9'8" Digging Depth, 15' 1" Total Reach
-
Wacker Neuson Compact Light Tower LTT4
Wacker Neuson Compact Light Tower LTT4 Compact light tower w/4-320w LED lights and a adjustable vertical mast, Duplex outlets The LTT4 light towers offer a smaller footprint, and the long-lasting LED's deliver exceptional light coverage for a variety of applications where temporary lighting is needed. The units are equipped with auxiliary power which adds to the versatility of these machines. LED Lights Rated to last the life of the machine, the durable LED lights eliminate frequent bulb replacement expense, reducing the total cost of ownership Four 320 Watt LED lights provide a total of 192,000 Lumens instantaneously and increase uptime by eliminating warm-up and cool-down periods Efficient LED lights extend the machine's run time and reducing overall operating costs Programmable Controller Easy to use controller Allows for customizable start up and shut-downs as well as monitors fuel usage and alarms when fuel is low Heated display for cold weather conditions Compact Design Foldable tongue minimizes the machine footprint for shipping and storage Fork pockets and lifting eye make it easy to load, unload, and place machine Compact design allows for 22 machines to fit on a 48 ft trailer and 24 machines on a 53 ft. trailer Standard Auxiliary Power 2700 Watts to 4700 Watts auxiliary power allows for the use of power tools and other equipment while the lights are running Telescopic Vertical Mast The compact telescopic vertical mast design reduces storage and transportation area, improving logistics efficiencies. Manual, dual handle winch enables quick raising and lowering of mast. Extended 1,000 Hour Service Interval 1,000 hour oil change interval means more time working and less time servicing, reducing total cost of ownership. GENERATOR Metric Imperial Generator Manufacturer Mecc Alte Mecc Alte Voltage accuracy 10,0 % 10,0 % Gen. Rating 1~ (Cont.) [kW] 4,5 kW 4,5 kW Output frequency 60 Hz 60 Hz OPERATING FLUIDS Metric Imperial Run Time (Lights only) 211,1 std 211,1 std Fuel consumption (Lights only) 0,9 L/Std 0,2 GPH US LIGHTING - OUTPUT DETAILS Metric Imperial Coverage area 670 m2 7.211,9 ft2 Illuminance 54 Lux 5,0 fc ENGINE Metric Imperial Cylinder 2 2 Cooling Water-cooling Water-cooling Exhaust-gas limit EPA Tier 4 final EPA Tier 4 final Engine Manufacturer Kohler Kohler Cylinder capacity 686 cm3 41,9 Inch3 Tank capacity 198,40 l 52,4 gal US Operating Engine speed 1.800 1/min 1.800 1/min Effective power 5,5 kW 7,4 hp Engine type Diesel engine Diesel engine ELECTRICAL SYSTEM Metric Imperial Lighting appliances 320W (LED) 320W (LED) Bulb power 320 W 320 W MECHANICAL DETAILS Metric Imperial Operating weight 680,0 kg 1.499,1 lb Length 2.563 mm 100,9 " Height 2.548 mm 100,3 " Mast height max. 7,0 m 23,0 Foot Width 1.207 mm 47,5 "
-
WIFO 48" Multi-Purpose Power Rake
Multi-Purpose Power Rake Rake only Attachment Product features 48" Width 600lbs. weight 9" Drum Size 48 Teeth on drum 1.25" Length Optical carbide teeth 16x16.5 Air Front Wheel size 10-14GPM Hydraulic Requirements Hydraulic Angle 12 Volt for angling Required Case Drain Required
-
Wacker Neuson Trench Roller, RTD-SC4
Wacker Neuson Trench Roller - RTD-SC4 Remote Control, 19.8 hp Compaction Performance: Operating Weight: Approximately 3,295 lbs (1,495 kg). Another source gives the operating weight as 3,209.9 lb (1,456 kg). Drum Widths: Adjustable between 23.6 in (60 cm) and 32.3 in (82 cm). Dual section drums offer this flexibility. Centrifugal Force: 34.2 kN (low) / 68.4 kN (high). Frequency: 41.7. Another source gives the frequency as 42 Hz. Travel Speed: Up to 1.5 mph (2.5 km/h). Another source gives 0.8 - 1.7 m/H (1.3 - 2.7 km/h). Dimensions: Length: 75.5 in (1,918 mm). Width: 32.3 in (820 mm). Height: 51.2 in (1,300 mm). Wheelbase: 42.5 in (1,080 mm). Turning Radius: 61.0 in (1,549 mm).
-
Rental Paladin 42" Brush Grapple, 659244
Rental Paladin 42" Brush Grapple Item # 659244 All rental equipment is available at our Higginsville location: Address:19677 NW Outer RdHigginsville, MO 64037 Phone:660-584-8757 Contact us for availability, rates, and booking.
-
Rental Ironcraft 44" Mini Tiller Dingo, 00452706
Rental Ironcraft 44" Mini Tiller Dingo Item # 00452706 All rental equipment is available at our Higginsville location: Address:19677 NW Outer RdHigginsville, MO 64037 Phone:660-584-8757 Contact us for availability, rates, and booking.
-
Rental Trencher with 8" x 48" Dirt Chain, XTrench48, 306405
Rental Trencher with 8" x 48" Dirt Chain, XTrench48 Item # 306405 All rental equipment is available at our Higginsville location: Address:19677 NW Outer RdHigginsville, MO 64037 Phone:660-584-8757 Contact us for availability, rates, and booking.
-
Ironcraft 44" Brush Cutter Dingo, DBC44, 276777
Ironcraft 44" Brush Cutter Dingo, DBC44 Stock # 276777 All rental equipment is available at our Higginsville location: Address:19677 NW Outer RdHigginsville, MO 64037 Phone:660-584-8757 Contact us for availability, rates, and booking.
-
SM100 Wacker Rental
SM100 Wacker $240.00 Daily $840.00 Weekly All rental equipment is available at our Higginsville location: Address:19677 NW Outer RdHigginsville, MO 64037 Phone:660-584-8757 Contact us for availability, rates, and booking.
When it comes to finding parts for specific tractor models, you've got a range of options to ensure your equipment runs smoothly. Here's a detailed list of the models for which parts are readily available:
- Explorer Series: Focused on the Explorer 75T model, designed to handle tough terrains.
- Compact and Utility Models:
- Advanced Models:
- Heavy-Duty Options:
- High-Capacity Models:
- Land Series:
This lineup ensures that whether you're dealing with compact utility tasks or demanding agricultural operations, there are parts available to keep any of these models up and running efficiently.
How to Ensure Your Tractor Parts Are Compatible with Your Model and Year
When it comes to ordering the right tractor parts, compatibility with your specific model and year is crucial. Here's how you can make the right choice:
Start by carefully identifying the model of your tractor. Look for parts that include a detailed list of compatible tractor models. This information is usually clearly stated to help you determine if a part will fit your machine.
Pay close attention to any specific years that are mentioned. Some parts are designed for certain model years due to design tweaks and changes made by manufacturers. Ensuring that your tractor's year matches those listed can prevent compatibility issues.
Most part listings include a 'Fits Models' section. This list is invaluable for making sure you're selecting a part that will seamlessly integrate with your tractor.
If you’re unsure, consult a professional or a trusted dealer. They can offer expert advice and may even have access to cross-reference systems that can confirm part compatibility.
Before finalizing your order, double-check the model and year once more to ensure everything aligns. This simple step can save you from unnecessary hassle and return processes.
Following these steps will help you select the right parts the first time, ensuring your tractor remains in top working condition without unnecessary delays.